You are looking for a paper slitter rewinder. You have seen the spec sheets. You have compared prices. But there are a few traps that first‑time buyers often fall into. Let us walk through them so you do not waste time or money. Users who have not yet viewed the specifications table can refer to the parameter table in the appendix at the end of the article.
Mistake 1: Ignoring The Real Width Of Your Material
Some buyers look only at the model number. “YG‑1300” sounds like it handles 1300mm, right? Yes. But your raw material might be 1290mm wide. That leaves only 10mm of margin. What if your next order uses 1320mm paper? Then your paper slitter rewinder cannot take it.
The safer choice is to add 200‑300mm of buffer. If your current roll is 1250mm, consider the YG‑1600 (1600mm max width). You will thank yourself later when a wider job comes in.
Here are the actual widths from the product data:
- YG‑1300: 1300mm
- YG‑1600: 1600mm
- YG‑1800: 1800mm
Do not buy the smallest size that barely fits today‘s roll. Buy the size that fits next year‘s rolls, too. A paper slitting machine for sale with extra width costs more now, but it saves you from buying another machine later.
Mistake 2: Forgetting About The Slitting Width Range
The spec sheet says minimum slitting width is 30mm. That is true for all three models. But some buyers assume they can slit 20mm or 15mm. You cannot.
If your customer wants 25mm wide tape rolls, this paper slitter rewinder will not work. The blades and the rewind shaft are designed for 30mm as the lower limit.
Also check the maximum rewind diameter: ￠1000mm for all models. Unwind diameter: ￠1400mm. Many buyers remember the width but forget the diameter. A 1000mm rewind roll is quite large — about one meter across. Make sure your downstream packing line can handle that size.
Mistake 3: Underestimating The Weight And Space Needed
Look at the numbers:
| Model | Weight | Floor space (L×W) |
| YG-1300 | 4000 kg | 3300×3150 mm |
| YG-1600 | 4500 kg | 3300×3450 mm |
| YG-1800 | 5500 kg | 3300×3650 mm |
A 5.5‑ton paper slitter rewinder needs a concrete floor. Not every workshop can handle that load. Also the machine length is 3.3 meters, but you need extra space for loading raw rolls (another 2‑3 meters in front) and unloading finished rolls (another 2‑3 meters behind). Total space needed is roughly 8‑10 meters in length.
One customer bought a YG‑1800 without measuring his door. The machine arrived and could not fit through the workshop entrance. He had to hire a crane to lift it over the wall. Do not be that customer.
Mistake 4: Overlooking The Power Supply And Air Compressor
Standard power: 380V / 50Hz / 3‑phase. Total power ranges from 24kw (YG‑1300) to 30kw (YG‑1800). That is not a small plug. You need a proper electrical panel and a dedicated circuit.
Also, this paper slitting machine for sale needs compressed air. The spec sheet does not list air consumption, but the machine uses air for core chucks, brake systems, and some tension controls. You will need an air compressor (about 7.5‑11kw is typical). Do not forget to budget for that.
If your facility has 220V or 60Hz power, you have two options: add a transformer (we can recommend one) or order a custom‑built motor (longer delivery time). Ask us before you place the order.
Mistake 5: Not Testing The Material First
You have paper. You have film. You have foil. Will they all slit cleanly on a paper slitter rewinder? Probably yes.
But “probably” is not good enough. If you are slitting a material that is very slippery, very thick, or very sticky, you should send us a sample roll, or you can tell us the material of the sample. We will run it on our paper slitting machine for sale and send you a video. You will see the edge quality, the tension stability, and the rewind firmness.
Do this before you pay. It costs little and saves big headaches.
Bonus: What The Spec Sheet Does Not Tell You
- Delivery time: 10‑30 working days. Larger models take longer.
- Installation: Our engineer charges $100 per day plus travel. Installation takes 5‑8 days on-site.
- Warranty: One year. Lifetime technical support.
- Optional features: Corona treater (for film surface treatment), voltage transformer, and custom slitting widths.
- Operation: One person is enough. The machine is designed for single‑operator use.
Final word
A paper slitter rewinder is a long‑term investment. The three YG models (1300, 1600, 1800) share the same speed (≤350 m/min), same unwind/rewind diameters, and same high build quality. The differences are width, weight, and power.
Choose based on your widest expected role. Leave room for growth. Prepare your floor and power. Test your material.
That is how you buy a slitter rewinder without regret.
The Parameter Table In The Appendix Is As Follows:
| Model | YG- 1300 | YG- 1600 | YG- 1800 |
| Max width | 1300mm | 1600mm | 1800mm |
| Max Diameter for unwinding | ￠1400mm | ￠1400mm | ￠1400mm |
| Min width of slitting | 30mm | 30mm | 30mm |
| Max Diameter of rewinding | ￠1000mm | ￠1000mm | ￠1000mm |
| Speed | ≤350m/min | ≤350m/min | ≤350m/min |
| Total Power | 24kw | 26kw | 30kw |
| Power supply | 380V/50hz | 380V/50hz | 380V/50hz |
| Weight | 4000kg | 4500kg | 5500kg |
| Overall dimension(LxWxH) | 3300x3150x1930(mm) | 3300x3450x1930(mm) | 3300x3650x1930(mm) |
